![]() ![]() Ebay shows an estimated ship time, that is exactly what it is.ESTIMATED! We will ship it within our time frame stated but cannot always depend on the shipping carriers. If you purchase an item on Friday, Saturday or Sunday, it will be shipped on the next business day. ![]() Please be advised that we do not ship on weekends or holidays. If you'd like to exchange an item that you purchased, you will be responsible for the cost difference and the shipping cost for the new product. When we receive the returned product, we will credit your account the full purchase price less the actual shipping cost. If you wish to return the item you purchased, you will be responsible for the shipping cost to send it back to us. Taking the speedfeed apart started with pressing two tabs and wiggling the larger side (with center spring) off.My S1400 is similar to many trimmers in that it. It is how we represent ourselves on Ebay. From here you put the hiperfire springs back (can be found online).Our main priority is to get you a genuine echo part with fast shipping and good communication. I use a punch to help wiggle through the hole once both disconnectors are on the pin: ![]() Press down on the shelf of the echo disconnector while pushing up on the tail end and press pin through echo disconnector hole (same as the semi disconnector above): Make sure the spring stays in the notch of the trigger pack: Slide the hole in the bottom of the echo disconnector over the spring. There are several videos on YT that shows you how to BulletProof the Speed Feed 400. Place the echo disconnector spring into the spring notch: But I loaded the same echo trimmer line I had been using in the speed feed 400 and it’s doesn't break like with the badger head, I haven’t seen any wear on the surface of the head that touches the ground it’s only 3 weeks so still early. I use a punch small enough to fit in the echo disconnector spring so that it will slide off the punch. It seems to me that the speed feed should also fit tightly. So I put my stihl head back on the trimmer and the metal base plate and the back side of the stihl head fit tightly together and they spin together. You want it to go far enough to hold the semi disconnector while also leaving a gap for the echo disconnector: When I run the trimmer the base plate spins independently of the speed feed and it makes a whining sound. Then take the other pin and insert from the same side as the semi disconnector, using the same technique above. Then I press down on the trigger pack to push the pin through: An easy way I found was place the pin on the bench (or a piece of wood), partially through the hole, while pressing down on the disconnector shelf with a punch, and lifting up on the tail end of the trigger (under the back-up disconnector). Take one of the large pins and push through the hole from the opposite side of the semi disconnector. Slide the trigger back into the frame (you will have to press down on the disconnector for this): Put the semi disconnector spring into the right-side hole (looking face on) and place the semi disconnector over the spring: It should pop into place without too much force: Replace the spring and press the bottom of the spring with a small punch, while pulling the disconnector back. Press forward on the back-up disconnector and the spring will pop out of place (great because removing the pin that the c-clip is holding is a PITA): Remove the trigger section from the trigger pack frame:īelow is the back-up disconnector spring that was replaced On my newer echo both springs were the same: I kept the stiffer spring under the echo disconnector, and the lighter spring under the semi disconnector. For this trigger, the factory disconnector springs were different. Tap out the large pin that holds the disconnectors with a punch and hammer (face on view, the semi disconnector, with the tail, will be on the right. Take a close look at how the disconnectors sit in the trigger pack: This should push out with a little force or light hammer taps and a punch: Next I removed the hammer and hammer spring. Remove the hiperfire springs by placing your hand over the hammer pushing up on the tail end of the trigger pack: The spring I replaced was the under the back up disconnector for this one, the semi & echo disconnectors have factory springs. This is the step by step process on how I change out the disconnector springs for the echo trigger. Only modification is changing the back up disconnector spring. The semi-mode trigger pull is right around 3lbs.Įcho mode initial pull is roughly 3.5lbs and the echo reset is a hair over 4.5lbs. It is highly encouraged that you do the simplified install method shown by Gator McKlusky in the video at the top of the page ![]() This is the original tutorial for installing the replacement spring in your fostech echo. We are not liable for any damages your rifle or person and this may void your warranty. This spring has no affiliation with Fostech Inc. ![]()
0 Comments
Leave a Reply. |